CAT 908

As Pás de Rodas Cat® definem o padrão de produtividade, eficiência de combustível e conforto do operador. A Pá de Rodas Compacta Cat 908 possui um motor C2.8 de alto binário que funciona em conjunto com um sistema de transmissão hidrpestática inteligente para fornecer eficiência de combustível excepcional. Os diferenciais de travamento “Shift on the go” e a transmissão hidrostática proporcionam uma operação suave e potente, ao mesmo tempo em que aumentam a eficiência dos ciclos da máquina.

Especificações

Potência Bruta Máxima55.7 kW
Modelo do MotorCat C2.8*
Torque Bruto Máximo – ISO 14396300 N·m
Diâmetro Interno90 mm
Curso110 mm
Deslocamento2.8 l
Observação*Meets U.S. EPA Tier 4 Final and EU Stage V emission standards.
Observação (1)Maximum gross and net torque measured at 1,600 rpm.
Observação (2)Net power ratings are tested at the reference conditions for the specified standard.
Potência Bruta Máxima – ISO 1439655.4 kW
Observação (3)Net power advertised is the power available at the flywheel.
Peso Operacional6632 kg
Capacidades da Caçamba0.75-1.55 m³ (1.0-2.0 yd³)
Multiuso0.75-1.1 m³ (1.0-1.4 yd³)
ObservaçãoAll capacities are applicable for each model. Bucket selection must be made with an understanding of the material density and application to ensure machine stability is maintained within the tipping loads stated per model and configuration.
Maximum Gross Power – Rated Engine Speed2400 r/min
Rated Net Power – Rated Engine Speed2400 r/min
Maximum Gross Power – ISO 14396 (metric)75.3 mhp
Rated Net Power – SAE J134954.2 kW
Maximum Engine Speed2550 rpm
Rated Net Power – ISO 924953.8 kW
Maximum Gross Torque – SAE J1995300 N·m
Maximum Gross Power – SAE J199555.7 kW
Maximum Net Torque – SAE J1349296 N·m
Maximum Net Torque – ISO 9249295 N·m
Rated Net Power – 2,400 rpm – ISO 9249 (metric)73.1 mhp
Height: Ground to Cab**2670 mm
Height: Ground to Beacon**2853 mm
Height: Ground Axle Center**519 mm
Height: Ground Clearance**320 mm
Length: Overall*6163 mm
Length: Rear Axle to Bumper1391 mm
Length: Hitch to Front Axle1085 mm
Length: Wheel Base2170 mm
Clearance: Bucket at 45° *3294 mm
Clearance: Load over Height**4238 mm
Clearance: Level Bucket**3682 mm
Height: Bucket Pin**3889 mm
Height: Overall**4789 mm
Reach: Bucket at 45° *1042 mm
Carry Height: Bucket Pin508 mm
Dig Depth**72 mm
Width: Bucket2080 mm
Width: Tread Center1570 mm
Turning Radius: Over Bucket4869 mm
Width: Over Tires1990 mm
Turning Radius: Outside of Tires4087 mm
Turning Radius: Inside of Tires2033 mm
Rack Angle at Full Lift70°
Dump Angle at Full Lift40°
Rack Angle at Carry47°
Departure Angle – Degrees30°
Articulation Angle – Degrees39°
Operating Weight: Bucket ^6762 kg
Tipping Load – Straight – ISO 14397-1 †4113 kg
Tipping Load – Full Turn – ISO 14397-1 †3446 kg
Operating Weight: Carriage and Tines ^^6771 kg
Tipping Load – Straight †3194 kg
80% of Tip: Firm and Level EN474-3 ††2152 kg
Note (1)*Vary with bucket
Note (2)**Vary with tire
Note (3)^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), 1.15 m3 (1.5 yd3) general purpose bucket.
Note (4)^^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), class III carriage, 1220 mm (4 ft) tines (500 mm [20 in] load center).
Note (5)†Full compliance to ISO 14397-1 (2007) Sections 1 thru 6 (fork 500 mm [20 in] load center), which requires 2% verification between calculation and testing.
Note (6)††Full compliance to EN474-3 and SAE J1197.
Note (7)#HPL-A weight, tipping and rated loads are within 1% of the HPL-V.
Note (8)Dimensions listed are for a machine configured with standard cab, heater, 20 km/h (12 mph), standard guarding, 80 kg (176 lb) operator, full fluids, SPT9 405/70 R20 tires and 1.15 m3 (1.5 yd3) general purpose bucket with bolt-on cutting edge or a class III fork carriage and tines, (tire supplier variability can impact dimensions by 2%).
Height: Ground to Cab**2670 mm
Height: Ground to Beacon**2853 mm
Height: Ground Axle Center**519 mm
Height: Ground Clearance**320 mm
Length: Overall*6319 mm
Length: Rear Axle to Bumper1391 mm
Length: Hitch to Front Axle1085 mm
Length: Wheel Base2170 mm
Clearance: Bucket at 45° *3131 mm
Clearance: Load over Height**4238 mm
Clearance: Level Bucket**3675 mm
Height: Bucket Pin**3889 mm
Height: Overall**4880 mm
Reach: Bucket at 45° *1098 mm
Carry Height: Bucket Pin529 mm
Dig Depth**80 mm
Width: Bucket2080 mm
Width: Tread Center1570 mm
Turning Radius: Over Bucket4912 mm
Width: Over Tires1990 mm
Turning Radius: Outside of Tires4087 mm
Turning Radius: Inside of Tires2033 mm
Rack Angle at Full Lift66°
Dump Angle at Full Lift33°
Rack Angle at Carry41°
Departure Angle – Degrees30°
Articulation Angle – Degrees39°
Operating Weight: Bucket ^6862 kg
Tipping Load – Straight – ISO 14397-1 †3749 kg
Tipping Load – Full Turn – ISO 14397-1 †3126 kg
Operating Weight: Carriage and Tines ^^6834 kg
Tipping Load – Straight †2923 kg
80% of Tip: Firm and Level EN474-3 ††1982 kg
Note (1)*Vary with bucket
Note (2)**Vary with tire
Note (3)^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), 1.15 m3 (1.5 yd3) general purpose bucket.
Note (4)^^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), class III carriage, 1220 mm (4 ft) tines (500 mm [20 in] load center).
Note (5)†Full compliance to ISO 14397-1 (2007) Sections 1 thru 6 (fork 500 mm [20 in] load center), which requires 2% verification between calculation and testing.
Note (6)††Full compliance to EN474-3 and SAE J1197.
Note (7)#HPL-A weight, tipping and rated loads are within 1% of the HPL-V.
Note (8)Dimensions listed are for a machine configured with standard cab, heater, 20 km/h (12 mph), standard guarding, 80 kg (176 lb) operator, full fluids, SPT9 405/70 R20 tires and 1.15 m3 (1.5 yd3) general purpose bucket with bolt-on cutting edge or a class III fork carriage and tines, (tire supplier variability can impact dimensions by 2%).
Height: Ground to Cab**2670 mm
Height: Ground to Beacon**2853 mm
Height: Ground Axle Center**519 mm
Height: Ground Clearance**320 mm
Length: Overall*5549 mm
Length: Rear Axle to Bumper1391 mm
Length: Hitch to Front Axle1085 mm
Length: Wheel Base2170 mm
Clearance: Bucket at 45° *2615 mm
Clearance: Load over Height**2957 mm
Clearance: Level Bucket**3197 mm
Height: Bucket Pin**3404 mm
Height: Overall**4304 mm
Reach: Bucket at 45° *770 mm
Carry Height: Bucket Pin353 mm
Dig Depth**109 mm
Width: Bucket2080 mm
Width: Tread Center1570 mm
Turning Radius: Over Bucket4570 mm
Width: Over Tires1990 mm
Turning Radius: Outside of Tires4087 mm
Turning Radius: Inside of Tires2033 mm
Rack Angle at Full Lift53°
Dump Angle at Full Lift45°
Rack Angle at Carry51°
Departure Angle – Degrees30°
Articulation Angle – Degrees39°
Operating Weight: Bucket ^6632 kg
Tipping Load – Straight – ISO 14397-1 †4812 kg
Tipping Load – Full Turn – ISO 14397-1 †4060 kg
Operating Weight: Carriage and Tines ^^6467 kg
Tipping Load – Straight †3920 kg
80% of Tip: Firm and Level EN474-3 ††2638 kg
Note (1)*Vary with bucket
Note (2)**Vary with tire
Note (3)^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), 1.15 m3 (1.5 yd3) general purpose bucket.
Note (4)^^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), class III carriage, 1220 mm (4 ft) tines (500 mm [20 in] load center).
Note (5)†Full compliance to ISO 14397-1 (2007) Sections 1 thru 6 (fork 500 mm [20 in] load center), which requires 2% verification between calculation and testing.
Note (6)††Full compliance to EN474-3 and SAE J1197.
Note (7)#HPL-A weight, tipping and rated loads are within 1% of the HPL-V.
Note (8)Dimensions listed are for a machine configured with standard cab, heater, 20 km/h (12 mph), standard guarding, 80 kg (176 lb) operator, full fluids, SPT9 405/70 R20 tires and 1.15 m3 (1.5 yd3) general purpose bucket with bolt-on cutting edge or a class III fork carriage and tines, (tire supplier variability can impact dimensions by 2%).
Main Relief – 1st Auxiliary (3rd slice)23500 kPa
Main Relief – 1st Auxiliary (3rd slice) – Standard Flow90 l/min
Main Relief – 1st Auxiliary (3rd slice) – High Flow125 l/min
Main Relief – 2nd Auxiliary (4th slice)23500 kPa
Main Relief – 2nd Auxiliary (4th slice) – Flow45 l/min
Hydraulic Cycle Time – Lift5.8 s
Hydraulic Cycle Time – Dump1.8 s
Hydraulic Cycle Time – Float Down3.6 s
Hydraulic Cycle Time – Rackback2.5 s
Note*Adjustable from 20% to 100% of maximum flow through display.
Tire Size – Standard*405/70 R20 SPT9
Tire Size – Optional405/70 R20 Powerloads
Tire Size – Optional (1)400/70 R20 XMCL/Bibload
Tire Size – Optional (2)360/80 R20 TRI 2
Tire Size – Optional (3)40X14-20 TL, SM/TR
Forward and Reverse – Speed Range Creep#10 km/h
Forward and Reverse – Speed Range 2** – High Speed18 km/h
Forward and Reverse – Speed Range 2** – Standard19 km/h
Forward and Reverse – Speed Range 3***40 km/h
Note (1)*Creep function not available in this gear or above.
Note (2)**Max speed dependent on model and configuration (standard vs. high speed transmission).
Note (3)***Reverse is 30 km/h (19 mph).
Forward and Reverse – Speed Range 1*10 km/h
Height: Ground to Beacon**2853 mm
Height: Ground Axle Center**519 mm
Length: Rear Axle to Bumper1391 mm
Length: Hitch to Front Axle1085 mm
Clearance: Load over Height**2957 mm
Height: Overall**4395 mm
Carry Height: Bucket Pin374 mm
Turning Radius: Outside of Tires4087 mm
Rack Angle at Full Lift49°
Rack Angle at Carry53°
Departure Angle – Degrees30°
Articulation Angle – Degrees39°
Operating Weight: Bucket ^6718 kg
Tipping Load – Straight – ISO 14397-1 †4347 kg
Tipping Load – Full Turn – ISO 14397-1 †3623 kg
Operating Weight: Carriage and Tines ^^6530 kg
Tipping Load – Straight †3649 kg
80% of Tip: Firm and Level EN474-3 ††2468 kg
Note (1)*Vary with bucket
Note (2)**Vary with tire
Note (3)^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), 1.15 m3 (1.5 yd3) general purpose bucket.
Note (4)^^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), class III carriage, 1220 mm (4 ft) tines (500 mm [20 in] load center).
Note (5)†Full compliance to ISO 14397-1 (2007) Sections 1 thru 6 (fork 500 mm [20 in] load center), which requires 2% verification between calculation and testing.
Note (6)††Full compliance to EN474-3 and SAE J1197.
Note (7)#HPL-A weight, tipping and rated loads are within 1% of the HPL-V.
Note (8)Dimensions listed are for a machine configured with standard cab, heater, 20 km/h (12 mph), standard guarding, 80 kg (176 lb) operator, full fluids, SPT9 405/70 R20 tires and 1.15 m3 (1.5 yd3) general purpose bucket with bolt-on cutting edge or a class III fork carriage and tines, (tire supplier variability can impact dimensions by 2%).
Height – Ground to Cab2670 mm
Height – Ground Clearance320 mm
Length – Wheel Base2170 mm
Length – Overall with Bucket5707 mm
Reach – Bucket at 45°872 mm
Dig Depth117 mm
Clearance – Bucket at 45°2502 mm
Clearance – Level Bucket3189 mm
Height – Bucket Pin3404 mm
Turning Radius – Over Bucket4613 mm
Turning Radius – Inside Tire2033 mm
Width – Bucket2080 mm
Width – Tread Center1570 mm
Width – Over Tires1990 mm
Dump Angle at Full Lift45°
NoteOscillation of ±11 degrees via hitch between front and rear frames.
Steering Cycle Times – (full left to full right) – at High Idle3 s
Steering Articulation Angle – Each Direction39 °
Note (1)Bucket capacities stated include BOCE, in line with ISO 7546.
Bucket Capacities – General Purpose0.80-1.35 m³ (1.0-1.7 yd³)
Bucket Capacities – Light Material1.25-1.55 m³ (1.6-2.0 yd³)
FrontalFixed Locking Differential (standard)
TraseiroFixed Locking Differential (standard)
Tanque de Combustível90 l
Sistema de Arrefecimento12 l
Transmissão2.4 l
ObservaçãoNo Diesel Exhaust Fluid (DEF) fluid needed on this size engine.
Cárter do Motor8.8 l
Reservatório Hidráulico44.6 l
Sistema Hidráulico – Incluindo Tanque70.5 l
ROPSISO 3471:2008
FOPSISO 3449:2005 Level II
Observação (1)Canopy and cab, Rollover Protective Structures (ROPS) are available worldwide. Canopy not available in EU.
Observação (2)The declared dynamic operator sound pressure levels per ISO 6396:2008*, when properly installed and maintained, is 71 dB(A).
Note (3)*Measurements were conducted with the cab doors and windows closed.
Note (4)The labelled sound power level for the CE marked configurations when measured according to the test procedure and conditions specified in 2000/14/EC is 101 dB(A). 99 dB(A) Low Sound – Option available.
Fluxo Máximo – Bomba de Direção46.7 l/min
Número de Giros do Volante de Direção – Totalmente à Esquerda para Totalmente à Direita ou Totalmente à Direita para Totalmente à Esquerda3.25 turns or 4.00 turns
Pressão Máxima de Trabalho – Bomba de Direção23000 kPa
Observação*This tire has been used for all dimension, stability and performance data.
Observação (1)Other tire choices are available. Contact your Cat dealer for details.
Observação (2)In certain applications, the loader’s productive capabilities may exceed the tire’s tonnes-km/h (ton-mph) capabilities.
Observação (3)Caterpillar recommends that you consult a tire supplier to evaluate all conditions before selecting a tire model.
Axles – Front Center Differential8.8 l
Axles – Rear Center Differential8.8 l
Observação#Factory default shown, can be adjusted to any speed up to 19 km/h (12 mph).
Capacidade de Reciclagem93%

Galeria de imagens